logo
Casa
Chi siamo
Profilo aziendale
Giro della fabbrica
Controllo di qualità
prodotti

macchina per l'omogeneizzazione a vuoto

Omogeneizzatore liquido

Dentifricio in pasta che fa macchina

Macchina per fare la maionese

Miscelatore cosmetico dell'emulsionante

alto miscelatore del taglio

Miscelatore di detersivi liquidi

Macchina per la miscelazione di liquidi

Ro Macchina per il trattamento dell'acqua

Serbatoi di stoccaggio in acciaio inossidabile

Imballaggio Mahcine

macchine di riempimento

Macchina di etichettatura
Eventi
Notizie
Casi
Blog
Contattici
citazione
english
français
Deutsch
Italiano
Русский
Español
português
Nederlandse
ελληνικά
日本語
한국
العربية
हिन्दी
Türkçe
indonesia
tiếng Việt
ไทย
বাংলা
فارسی
polski
Casa
Chi siamo
prodotti

macchina per l'omogeneizzazione a vuoto

Omogeneizzatore liquido

Dentifricio in pasta che fa macchina

Macchina per fare la maionese

Miscelatore cosmetico dell'emulsionante

alto miscelatore del taglio

Miscelatore di detersivi liquidi

Macchina per la miscelazione di liquidi

Ro Macchina per il trattamento dell'acqua

Serbatoi di stoccaggio in acciaio inossidabile

Imballaggio Mahcine

macchine di riempimento

Macchina di etichettatura
Eventi
Notizie
Casi
Contattici
citazione
bandiera

notizie dettagliate
Casa > Notizie >

Notizie aziendali su What are common operational problems and their solutions?

Eventi

Notizie

Casi
Contattici
Mrs. Samson Sun
yx011@chinayxjx.com
86--18665590218
Contatto ora

What are common operational problems and their solutions?

2026-01-05

What are common operational problems and their solutions?

Common issues and practical troubleshooting methods:

a. Uneven Paste Texture (Grainy/Lumpy)

Causes: Insufficient shear force, uneven addition of materials, or incomplete dissolution of thickeners.
Solutions: Increase homogenizing speed (within equipment limits); add dispersed phase slowly and uniformly; pre-dissolve thickeners completely; extend emulsification time by 5~10 minutes.

b. Excessive Air Bubbles in Paste

Causes: Vacuum level insufficient, homogenizing head not submerged, or material added too quickly.
Solutions: Improve vacuum level (-0.08~-0.095 MPa); ensure the homogenizing head is 2~3cm below material surface; add materials slowly under vacuum; extend vacuum defoaming time.

c. Paste Segregation (Oil-Water Separation)

Causes: Inadequate emulsification, improper temperature control, or incorrect phase ratio.
Solutions: Increase shear force or emulsification time; adjust temperature to optimal range (50~75℃); optimize oil-water phase ratio; add appropriate emulsifiers/stabilizers.

d. Equipment Overheating

Causes: Long-term high-speed operation, blocked ventilation ports, or insufficient lubrication.
Solutions: Pause operation to cool the motor; clean ventilation ports; add lubricant to rotating parts; alternate between high and low speeds during emulsification.

e. Leakage (Vacuum Models)

Causes: Damaged seals, loose tank lid, or vacuum pump failure.
Solutions: Replace O-rings/gaskets; tighten the tank lid; inspect and repair the vacuum pump; check for tank body damage.
bandiera
notizie dettagliate
Casa > Notizie >

Notizie aziendali su-What are common operational problems and their solutions?

Eventi

Notizie

Casi

What are common operational problems and their solutions?

2026-01-05

What are common operational problems and their solutions?

Common issues and practical troubleshooting methods:

a. Uneven Paste Texture (Grainy/Lumpy)

Causes: Insufficient shear force, uneven addition of materials, or incomplete dissolution of thickeners.
Solutions: Increase homogenizing speed (within equipment limits); add dispersed phase slowly and uniformly; pre-dissolve thickeners completely; extend emulsification time by 5~10 minutes.

b. Excessive Air Bubbles in Paste

Causes: Vacuum level insufficient, homogenizing head not submerged, or material added too quickly.
Solutions: Improve vacuum level (-0.08~-0.095 MPa); ensure the homogenizing head is 2~3cm below material surface; add materials slowly under vacuum; extend vacuum defoaming time.

c. Paste Segregation (Oil-Water Separation)

Causes: Inadequate emulsification, improper temperature control, or incorrect phase ratio.
Solutions: Increase shear force or emulsification time; adjust temperature to optimal range (50~75℃); optimize oil-water phase ratio; add appropriate emulsifiers/stabilizers.

d. Equipment Overheating

Causes: Long-term high-speed operation, blocked ventilation ports, or insufficient lubrication.
Solutions: Pause operation to cool the motor; clean ventilation ports; add lubricant to rotating parts; alternate between high and low speeds during emulsification.

e. Leakage (Vacuum Models)

Causes: Damaged seals, loose tank lid, or vacuum pump failure.
Solutions: Replace O-rings/gaskets; tighten the tank lid; inspect and repair the vacuum pump; check for tank body damage.
+8618665590218
Collegamento rapido
Casa Chi siamo prodotti Notizie Casi Contattici
Contatto rapido

Indirizzo

Via Xiangqu n. 8, zona di sviluppo economico di Chengnan, Gaoyou, Jiangsu, Cina

Telefono

86--18665590218

+8618665590218
La nostra newsletter
Iscriviti alla nostra newsletter per sconti e altro.
Norme sulla privacy |  Mappa del sito  | Buona qualità della Cina macchina per l'omogeneizzazione a vuoto Fornitore. © di Copyright 2025-2026 Yangzhou Aipuweier Automation Equipment Limited Company . Tutti i diritti riservati.